|Location:||Houston, TX, US|
USED WIRELINE UNIT, SKID MOUNTED WITH OPERATORâ€™S CABIN
REFURBISHED HOISTING SYSTEM:Drum Assembly of all steel construction with a capacity of 10,000 feet 9/16 inch wireline. A large diameter drum shaft with pillow block design bearings each end will be installed.Drum will be on raised platform for operator convenience.
Brake assembly will be of dual aluminum brake bands offering good stopping, holding, and heat dissipation characteristics. A mechanical brake lever, positive locking with an adjustable handle will be installed at operatorâ€™s console.
HYDRAULIC DRIVE SYSTEM:Drive assembly will be of chain and sprocket design with an idler tensioning system. The drive chain will be double pitch #60 (3/4 inch)configuration. A Sauer Danfoss Series 90100CC Closed Loop Transmission Pump will be installed with control lever located convenient on the operator console. Hydraulic motor will drive the transmission.
POWER SYSTEM:Power drive will be an air cooled Deutz 115HP, In-line 6 Cylinder, Four Stroke, 6.5 Litre,EPA 2 Tier diesel engine producing 95 continuous horsepower at 2100 rpm. The engine will have a safety shutdown system in the event low oil pressure should occur. Engine monitoring gauges will be installed with a voltmeter and tachometer/hour meter. A dry type air filter will be included. Fuel and oil filter systems are installed. A spark arresting muffler and rig saver type shutdown system will be installed. A fuel tank of at 40 gallon capacity with a sight level gauge. Drip pan with drain plug under the skid. The engine will drive the hydraulic pump.
MAIN HOISTING HYDRAULIC SYSTEM:Hydraulic assembly is closed loop design,2,000 psi working pressure and 3,000 psi intermittent duty, with a rugged duty hydraulic pump drive, gearbox and 5 CID Rineer motor.Control is a directional control valve with infinite drum speed control feature. An operator adjustable relief valve is installed as well. Cross port relief valving will be installed as added protection against pressure spikes for the hydraulic motor when heavy activity is being performed.A safety type pressure gauge, dual scale, is installed to monitor hydraulic working pressure.Hydraulic fluid is supplied from a large reservoir of t 20 gallon capacity with a breather/strainer filler cap and a sight level/temperature gauge. A hydraulic oil cooler will be installed to aid the reservoir in cooling of the hydraulic fluid. Filtration is suctioned by a suction separator and a return filter is featured, . A filter condition monitoring gauge is installed. All hoses and fittings are sized for maximum flow.
MEASUREMENT SYSTEM: NOT INCLUDED
OPERATORâ€™S CABIN: The operatorâ€™s cabin is all aluminum construction with a square tubing frame work for greater strength. The cabin is well insulated and will have a light colored FRP material covering the walls and ceiling. A well padded operatorâ€™s chair with back rest installed at console area. This seat is adjustable and swivel for operatorâ€™s comfort. A large viewing window will be located over the drum area and an opening window at entry door and opposite wall. A wide entry door with heavy duty hinges and access handle will be installed. A step over threshold will be incorporated into the door. Roof mounted AC/Heater is installed. The cabin will be approx. (5 foot deep x 7 foo t wide x 6 foot interior height. (1.5m x 2.1m x 1.8m) )
Operators console will be of stainless steel construction and all controls, switches, and gauges will be installed with operator safety,comfort and efficeiency in mind. The console will be located inside operator's cabin behind the drum assembly.
ELECTRIC AND ADDITIONAL SYSTEMS: Lighting is inside operator's cabin and over the drum area. Roof mount air conditioner/heater will be installed for cabin comfort
MOUNTING SKID:A channel construction skid is installed with drag pipes each end. The skid has protective lift rigging around the skid. Four point lifting eyes are installed as well as fork lift pockets for safer and easier handling of this equipment.